ductile iron · DN80–DN1200 · K9 / C40 · 6 m · ISO 2531 · EN 545
Ductile iron socket pipe
Centrifugally cast socket pipe K9 and C40 with cement mortar lining, DN80–DN1200, 6 m long
ductile iron · DN80–DN1200 · K12 · socket T / flange PN10–PN25 · EN 545
Ductile iron fittings
Bends, tees, reducers, collars and flanged pieces in class K12 for T-type sockets and PN10–PN25 flanges
- EN 545:2010
- ISO 2531:2009
- GOST ISO 2531-2012
- GB/T 13295-2019
- EN 1092-2:1997
- EN 14901
- K12
- K14
- QT450-10
Section
Key parameters
- Nominal diameter
- DN80–DN1200
- Thickness class
- K12; tees K14
- Bend angles
- 11¼°, 22½°, 45°, 90°
- Joints
- T-type socket for EPDM gasket; K-type mechanical socket; flange PN10, PN16, PN25 per EN 1092-2
- Coating
- epoxy at least 250 µm per EN 14901 inside and outside; cement mortar inside on request
- Casting
- sand cast, annealed
- Mechanical properties
- Rm ≥ 420 MPa, A ≥ 5 %, hardness ≤ 250 HB
Sizes and weight
Range of fittings
| Fitting | Version | Thickness class | Joints |
|---|---|---|---|
| Double-socket bend | Version11¼°, 22½°, 45°, 90° | Thickness classK12 | Jointssocket-to-socket |
| Flanged bend | Version11¼°, 22½°, 45°, 90° | Thickness classK12 | Jointsflange-to-flange |
| Duckfoot bend | Version90° | Thickness classK12 | Jointsflange-to-flange |
| Tee | Versionequal and reducing | Thickness classK14 | Jointssocket or flange |
| Reducer | Versionconcentric | Thickness classK12 | Jointssocket-to-socket or flange-to-flange |
| Double-socket collar | Versionplain-end jointing, repair inserts | Thickness classK12 | Jointssocket-to-socket |
| Flange-socket piece | Version— | Thickness classK12 | Jointsflange-to-socket |
| Flange-spigot piece | Version— | Thickness classK12 | Jointsflange-to-spigot |
| Double-flanged piece | Versionlength to specification | Thickness classK12 | Jointsflange-to-flange |
| Cap / blank flange | Versionsocket or flange type | Thickness class— | Jointssocket or flange |
Sizes and masses follow the tables of the standard named in the table heading; rows that cannot be verified are not listed.
Theoretical weight at steel density 7.85 g/cm³. Actual batch weight is by scale and mill certificate.
Description
Fittings for ductile iron pipe networks: bends of 11¼°, 22½°, 45° and 90°, tees, reducers, double-socket collars, flange–socket and flange–spigot pieces, double-flanged pieces and caps. They are cast from the same spheroidal graphite iron, but in sand moulds rather than centrifugally, with subsequent annealing; flanges are cast integrally with the body. For sand-mould castings the standard sets tensile strength not less than 420 MPa, elongation not less than 5 % and hardness not more than 250 HB.
Details
Wall thickness follows class K12, for tees K14: e = K·(0.5 + 0.001·DN). T-type sockets take the spigots of pipes and pieces on an EPDM gasket; K-type mechanical sockets with a gland flange and bolts are used where a dismountable joint is needed; flanges are drilled to EN 1092-2 for PN10, PN16 or PN25 — pressure and drilling are set in the specification, not by default. The standard coating is epoxy to EN 14901, not less than 250 µm inside and outside; on request a cement mortar lining is applied inside and zinc with bituminous varnish outside.
During inspection at the plant the bureau measures the connection dimensions: outside diameter of spigots with a calliper and circumferential tape, inside diameter of the socket and groove with a bore gauge, wall thickness at the end faces with a calliper, and for flanges the bolt circle diameter, number and diameter of holes against the EN 1092-2 drawing; bend angles against a template, epoxy coating thickness with a thickness gauge. The cast marking — plant mark, DN, angle or reduction, class, year — is checked against the schedule, the heat number against the plant's mill test certificate (MTC). The full set of gaskets, bolts and seals and the packing by type are checked separately.
Applications
- route turns and obstacle bypasses on water mains
- branches and tie-ins to the distribution network
- diameter changes at pumping stations and service connections
- assemblies with gate valves, hydrants and expansion joints via flanges
- switching chambers, manholes and reservoir pipework
- repair inserts and joining of spigots with collars
Packing and shipment
Fittings are packed on pallets or in timber crates by DN and type, flange faces closed with covers. Gaskets, bolt sets and seals are packed separately per the completeness schedule with a batch tag.
Grade equivalents
Equivalents are the nearest, not identical: the exact grade and standard are written into the contract.
| GOST | GB (China) | ASTM | EN | Note |
|---|---|---|---|---|
| VCh45 (GOST 7293-85) | GB (China)QT450-10 (GB/T 1348) | ASTM65-45-12 (ASTM A536) | ENEN-GJS-450-10 (EN 1563) | NoteNearest equivalents by strength and elongation. Pipe standards specify mechanical properties directly; the casting grade in the plant certificate is for reference. |
| K9 (GOST ISO 2531-2012) | GB (China)K9 (GB/T 13295) | ASTM— | ENK9 (EN 545:2006) | NoteWall thickness class: e = 9·(0.5 + 0.001·DN), not less than 6 mm. In the ISO 2531:2009 and EN 545:2010 editions pressure classification became the primary one, K9 is retained for continuity. AWWA C151 classifies by pressure; the thicknesses do not match. |
| C40 (GOST ISO 2531-2012) | GB (China)C40 (GB/T 13295-2019) | ASTM— | ENC40 (EN 545:2010) | NoteClass by allowable operating pressure of 40 bar. At the same DN the C40 wall is thinner than K9; the classes are not equated — the specification names one class and one edition of the standard. |
| Socket with rubber ring (GOST ISO 2531-2012) | GB (China)Socket T-type (GB/T 13295) | ASTMPush-on (AWWA C111/A21.11) | ENTyton / push-on (EN 545) | NoteTyton is a trade name of the joint. Socket seating dimensions are set by the standard, but the groove and gasket profile differs between plants: gaskets are ordered from the pipe manufacturer. |
| — | GB (China)GB/T 21873 | ASTM— | ENEN 681-1 / ISO 4633 | NoteEPDM sealing gaskets for drinking water. Gasket requirements are checked against EN 681-1 and ISO 4633, which GOST ISO 2531-2012 references. |
| — | GB (China)GB/T 17457 | ASTMAWWA C104/A21.4 | ENISO 4179 / EN 545 | NoteCement mortar lining. Nominal thickness to ISO 4179: 3 mm for DN80–DN300, 5 mm for DN350–DN600, 6 mm for DN700–DN1200. |
| GOST 33259-2015 (PN10, PN16) | GB (China)GB/T 17241.6 | ASTMASME B16.1 (Class 125) | ENEN 1092-2 (PN10, PN16, PN25) | NoteFlange connection dimensions PN10 and PN16 to EN 1092-2 and GOST 33259 coincide for most DN and are checked against the drawing. ASME B16.1 has a different bolt-hole pattern and does not mate with EN flanges. |
Equivalents are the closest match, not identical: chemistry and tolerances differ between standards. The exact grade and standard are written into the contract.
The batch is checked against the order at the mill before shipment: sizes, markings, heat numbers on the certificate and tags, packing
Documents
What arrives with the steel
01
Mill test certificate (MTC)
Heat number, chemical composition, mechanical properties and standard for every heat in the batch.
02
Photo-documented inspection report
Measurements, markings, packing, weighing and bundle numbers, drawn up at the mill before shipment.
03
Specification and packing list
Items, sizes, quantities and mass by bundle: what the warehouse acceptance is checked against.
04
Certificate of origin
Confirms the mill and country of manufacture for customs clearance.
Related items
Buyer questions
What to check in the plant's mill test certificate (MTC) for ductile iron pipes
Heat and batch number — the same on the pipe and in the certificate; standard and class (K9 or C40) — the same as in the contract; mechanical properties: tensile strength not less than 420 MPa, elongation not less than 10 %, hardness not more than 230 HB; the result of the works hydrostatic test of each pipe; cement mortar lining thickness and zinc weight per square metre; type and material of the sealing gasket. A certificate without a heat number or with a different edition of the standard is returned to the plant before shipment.
How class K9 differs from C40 and what to write in the specification
K is a wall thickness class: e = K·(0.5 + 0.001·DN); for K9 and DN300 that is 7.2 mm. C is a class by allowable operating pressure in bar: a C40 pipe is rated for 40 bar, the wall is calculated from the pressure and at the same DN comes out thinner than K9. Both systems run in parallel in the ISO 2531:2009 and EN 545:2010 editions. In the specification name one class and one edition of the standard — thickness, weight and the works test of the batch are derived from them.
How the weight and volume of a batch are calculated
Ductile iron pipes are counted in pieces and metres; weight is taken from the standard's table for the class — barrel weight per metre plus socket weight — not from the steel-product formula, since the density of cast iron is 7.05 g/cm³. Fittings are counted in pieces per the schedule, weight per the plant catalogue. For transport the volume is calculated: the number of packages and the transport depend on DN and length, not on tonnage alone. The batch is sized to your volume — send us a specification with DN, class, length, joint type and coatings.
What the bureau's inspector checks at the plant before shipment
The spigot outside diameter with a circumferential tape, wall thickness at the end face with a calliper, thickness along the barrel with an ultrasonic thickness gauge; cement lining thickness and absence of cracks and delamination; the socket and sealing groove; the cast marking — plant mark, DN, class, year; the heat number on the pipe against the certificate; the full set of gaskets and lubricant; stacking on bearers before loading. The result is an inspection report with photographs.
Are pipes and fittings from different plants compatible
In connection dimensions — yes: the spigot outside diameter and socket seating dimensions are set by the standard, flanges to EN 1092-2. In the sealing gasket — no: each plant has its own groove and gasket profile, and another plant's gasket does not fit the socket. The bureau orders pipes, fittings and gaskets from one manufacturing plant or agrees compatibility with the plants in writing before the contract.
Price request
Send your specification and we will quote your batch
Price depends on grade, size, tonnage and delivery terms on the day of contract.
Request received